Results Indicate Transitional RIRGS Halo Position
Released
Released
Announcement PDF
Right Resources Limited
ABN 81 649 632 744 www.rightresources.com.au
41-47 Colin Street
West Perth WA 6005
ASX Announcement
+61 8 6245 2050
ASX:RRE
4 June 2026
Results Indicate Transitional RIRGS
Halo Position at Pilot;
Higher-Grade Targets Untested
Highlights
• Drilling confirms position within RIRGS model; core remains untested: Results from
RRPT0001 and RRPT0004 are consistent with the transitional halo of a RIRGS system, aligned
with the preliminary CODES (UTAS) model (ASX: 26 May 2026). The proximal high-grade
Au–Bi–Te–W core remains untested and represents a priority exploration target zone.
• Low grades reflect position in the system, not system potential: Gold in low-frequency quartz
veins with arsenic is consistent with drilling in the transitional halo, as predicted by the model.
This is expected and does not reflect the grade potential of the overall system. Historic high-
grade production (~38 g/t Au) demonstrates the presence of significantly higher-grade
mineralisation.
• Evidence of high nugget gold supports upside potential: Variability between Fire Assay (FA)
and PhotonAssay (PA) results, including 8.55m @ 0.2 g/t Au (FA) vs 0.3 g/t Au (PA) and a
maximum FA grade of 5 g/t Au increasing to 6.46 g/t Au (PA) in RRPT0001, is consistent with
high nugget, unevenly distributed gold.
• Large, coherent mineralised system defined: Gold-bearing quartz veining has been intersected
across ~70 metres of strike within a 2.4km x 2.9km system footprint, supporting the presence of a
substantial RIRGS system.
• Third hole testing major structural corridor, assays pending: RRPT0002 intersects major
northeast-trending faults within the northwestern target area of the MTPR02 geophysical anomaly.
Core evaluation and assay testing are underway to assess the impact of structure on
mineralisation.
Right Resources Limited (ASX: RRE) (Right Resources or the Company) provides an update on assay
testwork at the Pilot Project, Tumbarumba, NSW.
Preliminary analysis by CODES (Centre for Ore Deposit and Earth Sciences, University of Tasmania), a
globally recognised research group specialising in large-scale ore deposit systems, indicates Pilot is consistent
with a Reduced Intrusive Related Gold System (RIRGS), supported by geological, geochemical and fluid
inclusion evidence. Within a RIRGS, mineralisation is zoned outward from an intrusive heat source. CODES
has established the following zonation framework for Pilot:
Table 1: CODES Zonation Framework for Pilot Project
Zone Metal signature Interpretation Drilling status
PROXIMAL Au-Bi-Te-W Higher-temperature, higher-grade
zone – proximal to intrusive centre
NOT YET DRILLED
TRANSITIONAL Au-As ± Ag Transitional halo - current drill
position
RRPT0001 and
RRPT0004
DISTAL Ag-Pb-Zn Outer margins of system Not targeted
2 www.rightresources.com.au
The low grades in RRPT0001 and RRPT0004 are consistent with drilling in the As-Au transitional zone,
characterised by low-frequency sheeted quartz veining. This is consistent with the behaviour predicted by the
preliminary CODES model. The Au+Bi+Te+W proximal core has not been tested. Historic production of ~38
g/t Au confirms the presence of higher-grade gold mineralisation within the system, however, the proximal
source of these grades remains untested by modern drilling.
The MTPR02 geophysical resistivity anomaly (~500m diameter, southeast of the historic workings) is
interpreted as part of an intrusive complex. RRPT0002 (1,400m) has been completed to test the northwestern
quadrant of the MTPR02 anomaly. A series of north-east trending faults have been identified through surface
magnetics and mapping, and tested by drillhole RRPT0002. Interpretation of displacement along these faults
using marker horizons is in progress, which will provide further clarity on the target position of the proximal
Au+Bi+Te+W core.
Assay Methodology - What PA Can and Cannot Tell Us
Original RRPT0001 results (42m @ 0.2 g/t Au) used 50g Fire Assay (FA). Following reinterpretation as a
RIRGS, methodology was reviewed. In RIRGS systems, gold can be coarsely and heterogeneously
distributed and is poorly represented by a 50g FA charge.
PhotonAssay (PA) uses a 300-500g crushed sample, is non-destructive, and is suited to detecting nugget-
style gold. Where PA returns higher grades than FA on the same material, this is consistent with
heterogeneous distribution. Bidirectional variability (PA both above and below FA across different intervals)
supports this interpretation and suggests it is not solely attributable to methodological bias.
PA has a lower detection limit of 0.02-0.15 g/t Au (ppm equivalent) (varies by laboratory), with accuracy
decreasing near this threshold. The Company will undertake additional testwork using Screen Fire Assay
(SFA, 500g-1,000g total pulp) to assess whether methodological differences influence reported grades,
particularly at lower detection levels. Results will be reported once analysed.
RRPT0001 - Select PA vs FA Comparison Results
Hole summary: 699.4m east beneath historic Pilot workings. Previously reported: 42m @ 0.2 g/t Au from
338m (FA, ASX: 5 February 2026). A full PA programme is in progress, with select intervals returned, having
passed QAQC and considered suitable for release. Further testwork using SFA is underway to assess lower
detection limits. PA results at or near detection limits are considered preliminary.
Table 2: RRPT0001 Fire Assay and PhotonAssay results comparison of representative intervals returned
From
(m)
To (m) Width
(m)
FA (g/t Au) PA (g/t Au) Variance Notes
346.45 355 8.55 0.20 0.30 +48% Sub-interval within vein zone
351.5 351.7 0.20 5.00 6.46 +29% Maximum FA grade - re-assayed
by PA
363 364 1.00 0.29 0.43 +48% Sub-interval within vein zone
368 369.9 1.90 0.11 0.02 -86% Sub-interval within vein zone
377 378 1.00 0.14 0.57 +307% Sub-interval of increased vein
intensity
All intervals are reported as downhole lengths; true widths are not known. Minor discrepancies in variances may arise due to rounding
and reporting precision.
Key observations: Intervals above the PA detection limit consistently upgrade under PA vs FA confirming
nugget-style gold. Gold is associated with arsenic; tungsten, bismuth, telluride and molybdenum are
subdued, which is consistent with the preliminary CODES transitional RIRGS position. Until PA and SFA is
complete, 42m @ 0.2 g/t Au (FA) remains the reported intersection.
3 www.rightresources.com.au
RRPT0004 - Initial PA Results
Hole summary: 441.1m, ~70-100m along strike north of RRPT0001. All PA results returned have passed
QAQC and are considered suitable for release. Further testwork using SFA is underway to assess lower
detection limits. PA results at or near detection limits are considered preliminary.
Table 3: RRPT0004 Fire Assay and PhotonAssay results comparison of representative intervals returned
From
(m)
To (m) Width
(m)
FA (g/t Au) PA (g/t Au) Variance Notes
342.3 346 3.7 0.49 0.46 -7% Higher-grade sub-interval. Above
PA detection limit
342.75 343.25 0.5 2.18 2.24 +3% Maximum FA grade - re-assayed by
PA
353.7 356.7 3.0 0.06 0.11 +84% FA and PA confirm variability
362.6 365 2.4 0.20 0.20 — Sub-interval within vein zone
All intervals are reported as downhole lengths; true widths are not known. Minor discrepancies in variances may arise due to rounding
and reporting precision.
Key observations: Strike continuity confirmed over 70m. PA vs FA variability up to 84% confirms the same
nugget-style distribution as RRPT0001. An identical geological setting and CODES interpretation applies -
both holes are interpreted to lie within the transitional RIRGS halo. Neither has tested the proximal Au-Bi-Te-
W zone.
Figure 1: Pilot Project cross section illustrating the results from hole RRPT0001 and RRPT0004
1.0m @ 0.43g/t Au fr 363m
4 www.rightresources.com.au
Combined Picture - System Scale and the Case for the Next Hole
RRPT0001 and RRPT0004 together define a coherent, large-scale mineralised system: gold in sheeted
veins over 70m of strike, within a 2.4 x 2.9 km footprint, consistent As-Au geochemistry, and an identical low-
sulphide, low frequency quartz sheeted vein and alteration assemblage.
Every observation in both holes aligns with the transitional RIRGS position. Consistency between observed
results and the model supported its application for ongoing targeting.
• RRPT0002 (results pending): 1,400m testing potential offset of predicted major northeast-trending
faults, within the MTPR02 anomaly – interpreted as part of an intrusive complex southeast of the
historic workings – and further testing metal zonation. Results to be released progressively.
• Phase 2 targeting: Designed using geophysical modelling and to test potential repetition of sheeted
vein zones and impact of northeast-trending faults on geochemical metal zonation, vectoring toward
the proximal Au-Bi-Te-W zone.
Next Steps
• RRPT0002 assays: Results released progressively
• SFA - RRPT0001 and RRPT0004: Validates PA results near detection limits; will determine final
reported grades
• CODES district update: Broader RIRGS framework for Tumbarumba pending
• Geometallurgy and dacite porphyry study: Gold form and distribution through CODES and Met-
Chem
Assay Testwork Program - Technical Detail
The methodology context relevant to interpreting results is outlined Appendix 1, Section 2. Technical detail
for JORC compliance is summarised below:
Original assays (50g FA): Bureau Veritas, Adelaide. PA testwork comprises 41 samples analysed at SGS
Orange and SGS Perth (all NATA-accredited). For each interval, all available sample mass was used;
between one and six sub-assays were completed per interval. OREAS certified reference material was used
for QC at each laboratory. Sample transport and turnaround times were impacted by national diesel fuel
supply disruptions (March to May 2026) and elevated laboratory demand.
ENDS
This announcement has been approved for release by the Board of Right Resources Limited.
5 www.rightresources.com.au
Further Information
Graham Howard
Managing Director
E: info@rightresources.com.au
Jessamyn Lyons
Company Secretary
E: jessamyn.lyons@rightresources.com.au
Media
David Tasker
Chapter One Advisors
E: dtasker@chapteroneadvisors.com.au
Follow Us
About Right Resources (ASX: RRE)
Right Resources Limited is a New South Wales-based mineral exploration company focused on advancing a
portfolio of gold, copper and critical mineral assets across 2,177 km² (GIS-derived) of tenements in the
Tumbarumba and New England regions, both located within historically significant goldfields and mineral
provinces.
The Company's flagship asset is the Pilot Project, a high-grade gold target in the Tumbarumba Region with a
history of high-grade underground gold production (~38 g/t Au), which is being advanced through a maiden
diamond drilling programme in collaboration with CODES (Centre for Ore Deposit and Earth Sciences,
University of Tasmania). The Blue Prospect tungsten discovery adds a significant critical minerals dimension
to the Company's portfolio.
Forward Statements
This announcement may contain forward-looking statements or information, including forecasts, projections,
opinions and conclusions. These statements are not guarantees of future performance or statements of fact.
Actual events and results may differ materially due to a variety of risks, uncertainties and other factors,
including, among other things, funding requirements, metal prices, exploration and development risks,
operational challenges, competition, production risks, regulatory restrictions, including environmental
regulation and liability, potential title disputes and various business, economic, political and social
uncertainties and contingencies. Although Right Resources believes there is a reasonable basis for any
forward-looking statements, such statements involve significant risks and uncertainties.
6 www.rightresources.com.au
Competent Person Statement
Graham Howard
The information in this announcement that relates to Exploration Results is based on and fairly represents
information and supporting documentation compiled by Graham Howard, who is Managing Director of Right
Resources Limited. Mr Howard is a Competent Person who is a Fellow of the Australian Institute of Mining
and Metallurgy (AusIMM).
Mr Howard has sufficient experience that is relevant to the style of mineralisation and type of deposit under
consideration, and to the activity being undertaken, to qualify as a Competent Person as defined in the 2012
Edition of the “Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore
Reserves” (JORC, 2012). Mr Howard consents to the inclusion in this announcement of the matters based
on his information in the form and context in which it appears.
Previously Reported Exploration Results
The information in this announcement that relates to the Company’s Exploration Results has been extracted
from the Company’s previous ASX announcements dated 26 May 2026, 5 February 2026 and 27 October
2025. The Company confirms that it is unaware of any new information or data that materially affects the
information included in those announcements. To the extent disclosed above, the Company confirms that the
form and context in which the Competent Person’s findings are presented have not been materially modified
from the original market announcements. All previously released market announcements referred to within
this announcement can be found on the Company’s website at rightresources.com.au.
7 www.rightresources.com.au
Appendix 1 - JORC Table 1, Sections 1 - 2
Section 1 Sampling Techniques and Data
Criteria JORC Code explanation Commentary
Sampling techniques • Nature and quality of sampling (eg cut
channels, random chips, or specific
specialised industry standard measurement
tools appropriate to the minerals under
investigation, such as down hole gamma
sondes, or handheld XRF instruments, etc).
These examples should not be taken as
limiting the broad meaning of sampling.
• Include reference to measures taken to
ensure sample representivity and the
appropriate calibration of any measurement
tools or systems used.
• Aspects of the determination of
mineralisation that are Material to the Public
Report.
• In cases where ‘industry standard’ work has
been done this would be relatively simple
(eg ‘reverse circulation drilling was used to
obtain 1 m samples from which 3 kg was
pulverised to produce a 30 g charge for fire
assay’). In other cases more explanation
may be required, such as where there is
coarse gold that has inherent sampling
problems. Unusual commodities or
mineralisation types (eg submarine nodules)
may warrant disclosure of detailed
information.
• Three primary Diamond Drill holes (DD)
(hole ID: RRPT0001, RRPT0002, and
RRPT0004), pre-collar RRPT0003 and
daughter hole RRPT0002A have been
completed or on hold by Right Resources
Limited (“Right Resources”, “RR”, or “the
Company”) at the Pilot Project Area in
EL9449.
• Diamond drilling was undertaken to obtain
high-quality core samples suitable for
geological and geotechnical logging
sampling and metallurgical testwork.
• Core was logged by a qualified geologist,
with intervals marked and cut for half-core
sampling to maintain representativity.
• Sample intervals typically ranged from 0.2
m to 1.0 m, adjusted based on lithology,
alteration, mineralisation and veining.
Certain intervals sampled a minimum of
0.15 m.
• Core was orientated, meter marked,
portable XRF (pXRF), magnetic
susceptibility and core loss recorded.
• Magnetic susceptibility readings were
taken over representative sections of each
hole using calibrated instruments, verified
against certified standards.
• pXRF readings were taken at 10cm
intervals were completed across
representative intervals for geochemistry
analysis.
• Downhole Geophysics: Geoscensor
Wireline completed acoustic televiewer, IP
& Resistivity, magnetic susceptibility
logging on RRPT0001, RRPT0002 and
RRPT0004
• These techniques are considered
appropriate for testing mineralisation
controls.
Drilling techniques • Drill type (eg core, reverse circulation, open-
hole hammer, rotary air blast, auger,
Bangka, sonic, etc) and details (eg core
diameter, triple or standard tube, depth of
diamond tails, face-sampling bit or other
type, whether core is oriented and if so, by
what method, etc).
• RRPT0001 - Diamond drilling was
undertaken with HQ (96mm outer
diameter) to 50.4mdh and then NQ2 with a
75.7mm drill bit (outer diameter) to
699.7m.
• RRPT0002 - Diamond drilling was
undertaken with HQ (96mm outer
diameter) to 479.3mdh and then NQ2 with
a 75.7mm drill bit (outer diameter) to
1400m
• RRPT0003 – Diamond drilling was
undertaken with HQ (96mm outer
diameter) to 300.2m
• RRPT0004 – Diamond drilling was
undertaken with HQ (96mm outer
diameter) to 441.1m
• RRPT0002A – Daughter hole of
RRPT0002 was drilled using in hole wedge
from 478m. Diamond drilling was
8 www.rightresources.com.au
Criteria JORC Code explanation Commentary
undertaken with HQ (398mm outer
diameter) to 677.5m). The Company plans
to complete this hole pending outcomes
from assays.
• Chrome barrel was used to limit hole
deviation
• Waste mud from the drilling program was
collected as part of environmental
monitoring.
• All core from each shift was quick logged
by a geologist.
• All core has been orientated, with drillers
marking core with down hole orientation
tool, recording rod counts and core loss
routinely for each hole.
• A geologist has either checked driller
orientation marks or undertaken full length
orientation mark up to validate orientation
markings, suitable for structural modelling.
Drill sample recovery • Method of recording and assessing core
and chip sample recoveries and results
assessed.
• Measures taken to maximise sample
recovery and ensure representative nature
of the samples.
• Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gain of fine/coarse material.
• Core loss was recorded after each run and
core block inserted by driller.
• Meter marking was undertaken from the
start of the hole which provides validation
against the core block interval depths.
• A final rod count after the hole is drill
provides a validation check on total meters
drilled.
• Laboratory measured weight of each
sample.
• Sample recoveries were generally high
and consistent across the drilling program,
with no observable relationship between
sample recovery and grade.
Logging • Whether core and chip samples have been
geologically and geotechnically logged to a
level of detail to support appropriate Mineral
Resource estimation, mining studies and
metallurgical studies.
• Whether logging is qualitative or quantitative
in nature. Core (or costean, channel, etc)
photography.
• The total length and percentage of the
relevant intersections logged.
• Geological logs have been completed
using a multi pass system capturing
lithology, alteration, mineralogy, veining,
structure and geotechnical RQD.
• Logging is completed at a level suitable to
support future resource estimation.
• Logging includes both qualitative and
quantitative elements. Qualitative
descriptions cover lithology, alteration
style, mineralisation characteristics, and
structural observations. Quantitative
measurements include RQD, fracture
frequency, veining percentages, mineral
abundance estimations, and other
geotechnical or analytical attributes.
• Core is photographed both as wet and dry.
• All holes have been logged with cut sheets
developed for sampling.
• Downhole geophysical logs of selected
intervals were completed for hole
RRPT0001, RRPT0002 and RRPT0004.
Sub-sampling
techniques and
sample preparation
• If core, whether cut or sawn and whether
quarter, half or all core taken.
• If non-core, whether riffled, tube sampled,
rotary split, etc and whether sampled wet or
dry.
• Intervals selected for sampling by a
geologist and half core cut using a
diamond saw.
• To minimise bias in sample selection, the
orientation line on the core is positioned
slightly off-centre in the core trays. This
ensures that the core is consistently cut in
9 www.rightresources.com.au
Criteria JORC Code explanation Commentary
• For all sample types, the nature, quality and
appropriateness of the sample preparation
technique.
• Quality control procedures adopted for all
sub-sampling stages to maximise
representivity of samples.
• Measures taken to ensure that the sampling
is representative of the in situ material
collected, including for instance results for
field duplicate/second-half sampling.
• Whether sample sizes are appropriate to the
grain size of the material being sampled.
the same position while preserving the
orientation mark. The half opposite the
orientation line is selected for sampling. A
cut line is placed to differentiate the
orientation line as an indication for cutting.
• All samples are derived from diamond
core.
• Sample preparation for Fire Assay includes
drying, crushing to <2 mm, and pulverising
to a nominal 85–90% passing 75 µm
completed at Bureau Veritas Adelaide.
• Sample preparation for PhotonAssay
includes drying, coarse crush of drill core
to 2mm to 3mm and split crushed material
to nominal 500g samples, completed at
ALS Orange sample preparation facility.
• Samples were also issued to SGS Orange
for sample preparation for PhotonAssay.
Preparation for PhotonAssay includes
drying and coarse crush to 2mm to 3mm
and spilt to nominal 300g samples for
analysis.
• The Company is conducting further
testwork on current diamond core and may
result in changes to sampling procedure.
This work includes preparation testwork for
both screen fire assay and fire assay to
extinction.
• Quality control procedures during
sub‑sampling include careful handling of
core, use of a fixed‑position core saw, and
routine cleaning between cuts to minimise
contamination.
• Sample sizes (half‑core) are subject to
ongoing testwork and may change based
on gold mineralisation styles Testwork is in
progress to determine if volume variance
(mass and volume of sample) influences
assay grade.
Quality of assay data
and laboratory tests
• The nature, quality and appropriateness of
the assaying and laboratory procedures
used and whether the technique is
considered partial or total.
• For geophysical tools, spectrometers,
handheld XRF instruments, etc, the
parameters used in determining the analysis
including instrument make and model,
reading times, calibrations factors applied
and their derivation, etc.
• Nature of quality control procedures
adopted (eg standards, blanks, duplicates,
external laboratory checks) and whether
acceptable levels of accuracy (ie lack of
bias) and precision have been established.
• The Company is completing a testwork
program using Fire Assay, PhotonAssay
and Screen Fire Assay on selected
intervals from holes RRPT0001,
RRPT0002 and RRPT0004 which are in
progress. Interim results for holes
RRPT0001 and hole RRPT0004 subject of
this Table 1.
• The company has adopted updated
methodology for assaying testwork,
PhotonAssay analysis which does not add
flux, require fusion, acids or dissolution,
and sample remains intact. The Company
then commences either a Fire assay or
Screen Fire Assay methodology. This may
require samples to be transported to other
assay laboratories which host relevant
services.
• PhotonAssay (X-ray fluorescence method)
analyses a sample mass of approximately
300g to 500g (laboratory dependent).
• Fire assay requires core samples to be
dried, crushed and pulverised. Smaller
mass of sample of 50g is split from
pulverised sample material for Fire assay
10 www.rightresources.com.au
Criteria JORC Code explanation Commentary
which involving adding flux, fusion,
cupellation and reporting.
• Holes RRPT003 and daughter hole remain
uncut pending outcomes from initial phase
of testwork. These holes may also be used
for future geochemistry and metallurgical
analysis.
• Internal laboratory QAQC protocols include
routine insertion of blanks, duplicates, and
certified reference material (CRMs).
• Company QAQC procedures for Photon
and fire assay and multi-element ICP
analysis:
o CRMs inserted at a frequency of 1 in
20 samples (5%), covering both gold
(Au) and milt-element suites.
o Blanks inserted at a frequency of 1 in
20 samples (5%) to monitor
contamination.
o Company completing duplicate
sampling of half core as part of
testwork.
o Laboratory pulp duplicates are
routinely analysed, as part of the
internal laboratory QAQC routine.
o Only results which have passed
QAQC are released.
• Instrument calibration:
o Magnetic susceptibility readings were
taken using a calibrated instrument
with periodic checks against known
standards.
o pXRF instrument is calibrated at
commencement of each sampling
run and periodic checks against
known CRM.
Verification of
sampling and
assaying
• The verification of significant intersections
by either independent or alternative
company personnel.
• The use of twinned holes.
• Documentation of primary data, data entry
procedures, data verification, data storage
(physical and electronic) protocols.
• Discuss any adjustment to assay data.
• CODES have independently reviewed drill
holes and taken samples to complete
testwork.
• Daughter hole RRPT0002A commenced
15 March 2026 will provide initial twin hole
data to parent hole RRPT0002. Potential
work includes future metallurgical testwork
with hole RRPT0002A.
• Drill logs have been recorded in electronic
format.
• All data is uploaded, validated and stored
in the Company’s Micromine Geobank
Database.
• Drill hole data analysed in Leapfrog and
Micromine.
Location of data
points
• Accuracy and quality of surveys used to
locate drill holes (collar and down-hole
surveys), trenches, mine workings and other
locations used in Mineral Resource
estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic
control.
• Location of drill holes were set out by an
independent surveyor from Rivland
Surveyors using survey-grade equipment.
• Final collar surveys for holes RRPT0001,
RRPT0002, and RRPT0003 were
completed on 29th January and 27
February 2026 by Rivland Surveyors
11 www.rightresources.com.au
Criteria JORC Code explanation Commentary
• Final collar survey for RRPT0004 was
completed by Rivland Surveyors 22 April
2026.
• Down hole surveys were completed during
drilling using a Gyro Single Shot tool at
30m increments.
• Final down hole survey for RRPT0001,
RRPT0002, RRPT0003, RRPT0004 were
completed using the Gyro Single Shot
system.
• All spatial data are recorded in MGA 94
Zone 55 with elevations referenced to
AHD.
• Topographic control is considered
adequate for Mineral Resource estimation
purposes, with collar positions tied into
established survey control by a licensed
surveyor.
Data spacing and
distribution
• Data spacing for reporting of Exploration
Results.
• Whether the data spacing and distribution is
sufficient to establish the degree of
geological and grade continuity appropriate
for the Mineral Resource and Ore Reserve
estimation procedure(s) and classifications
applied.
• Whether sample compositing has been
applied.
• Position of holes provides in Table 4 and
Figure 2.
• RRPT0002 was drilled to 1400m at an
azimuth orientated approximately 40
degrees to the south of RRPT0001,
providing an approximate drill-hole
separation of 680m at the target depth of
1400m.
• RRPT0004 was drilled to 441.1m at a
northerly orientation (approximately 12
degrees), from RRPT0001, designed to
tests beneath the deepest historical
workings along strike of hole RRPT0001.
• RRPT0003 was drilled to 330.2m,
approximately 18 degrees south of
RRPT0002 and at a steeper dip (10
degrees steeper).
• RRPT0002A was drilled as a daughter
hole from RRPT0002, commencing at a
downhole depth of 478 m.
• The current spacing is insufficient to
establish a degree of geological and grade
continuity appropriate for a Mineral
Resource estimation.
• No sample compositing has been
completed.
Orientation of data in
relation to geological
structure
• Whether the orientation of sampling
achieves unbiased sampling of possible
structures and the extent to which this is
known, considering the deposit type.
• If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to have
introduced a sampling bias, this should be
assessed and reported if material.
• The current drilling orientations are
considered appropriate for testing the
interpreted sheet‑style mineralisation.
• RRPT0001 and RRPT0004 were drilled
approximately west–east, and RRPT0002
was drilled to the southeast, which
together provide intersections that are
broadly perpendicular to the historically
recorded north–south mineralisation trend.
• RRPT0002 is drilled at a lower angle
(~45°) to this trend, allowing it to test
potential down‑dip and along‑strike
extensions base on historic mining
records.
• RRPT0003, drilled to 300m as a pre-collar,
is oriented to the south–southeast to test a
12 www.rightresources.com.au
Criteria JORC Code explanation Commentary
potential vein trend based on preliminary
geological interpretation.
• RRPT0002A is drilled as a daughter hole
from RRPT0002 and is positioned to the
north of the parent hole drill trace. Minimal
drill separation has occurred within the
current drilled meters of 198.5m from
479m down hole from the parent hole
RRPT0002.
• At this stage of the program, there is
limited detailed knowledge of the key
mineralised structures, and therefore it is
not yet possible to fully assess whether
any drilling orientation may introduce
sampling bias.
Sample security • The measures taken to ensure sample
security.
• After cutting and bagging, each sample
was placed in labelled plastic bag with a
unique sample ID.
• Samples were grouped into polywoven
bags, sealed with cable ties, and
documented on a sample dispatch sheet.
• The dispatch sheet include
Share your feedback
Discover